SUBCON-PLUS F4

D-SUB Connectors for Field Bus Systems -with Screw Terminal Connection SUBCON-PLUS co s. nt ne po The plugs are especially suited for use in RS 485 bus systems in which an incoming and an outgoing bus cable must be connected in one D-SUB connector. SUBCON-PLUS can be connected quickly and conveniently under field conditions without soldering or crimping tools. The plug-in contacts are connected to numbered screw terminal blocks and it goes without saying that there is a separate termination block for each of the two cable entries. This produces a systematic overview of the wiring and simplifies every system start-up. The connector is available as socket and pin version suitable for nearly all bus systems. The terminating resistors are connected at the start and end of the bus to the free second termination block or, in some versions, using a slide-type switch (version for PROFIBUS). m 1. Short Description The connectors, designed for the smallest dimensions, can be used for transmission speeds up to 12 Mbit/s. The shielded connector housing guarantees high immunity to interference. The direction from which the cables are introduced can be decided on-site. The connection block can be installed either in the upper or lower shell of the housing. It is thus possible to introduce the cable at an angle of 0° ... 90° from the right or the left. 16 60 10 44 on l in ec om Fig. 1 36 Fig. 2 Headquarters: © Phoenix Contact GmbH & Co. • Flachsmarktstraße 8-28 • 32825 Blomberg • Germany Phone +49-(0) 52 35-3-00 • Fax +49-(0) 52 35-3-4 1200 • http://www.phoenixcontact.com SUBCON-PLUS D-SUB Connectors for Field Bus Systems -with Screw Terminal Connection 2. Technical Data SUBCON-PLUS with two cable entries Fig. 3 2.1. Description Order No. Pin assignment e.g. for use in bus system: Pcs. Pkt. pin 27 61 82 6 1, 2, 3, 5, 6, 8 PROFIBUS MODBUS MODBUS-PLUS BITBUS ARCNET MULTI / MININET, B&R SYSTEM 2003, B&R P-NET 1 SUBCON-PLUS M2 pin 27 61 83 9 2, 3, 4, 5, 7, 9 CAN SUCONET K1, K2, Klöckner Moeller S-BUS, SAIA J-BUS, MERLIN GERIN 1 SUBCON-PLUS-PROFIB pin 27 44 34 8 3, 8, resistor can be connected via slide-type switch PROFIBUS to 12 Mbit/s 1 SUBCON-PLUS F1 socket 27 44 26 7 1, 2, 3, 5, 6, 8 MODBUS MODBUS-PLUS BITBUS ARCNET MULTI / MININET, B&R SYSTEM 2003, B&R P-NET 1 SUBCON-PLUS F2 socket 27 99 49 0 2, 3, 4, 5, 7, 9 CAN SUCONET K1, K2, Klöckner Moeller S-BUS, SAIA J-BUS, MERLIN GERIN 1 SUBCON-PLUS F3 socket 27 61 87 1 2, 3, 6, 7, 8, 9 CAN OPEN FIP 1 SUBCON-PLUS F4 socket 27 44 08 9 2, 3, 4, 5, 6, 7 CAN, KEBA 1 SUBCON-PLUS F5 socket 27 44 10 2 MODBUS, CEGELEC 1 12 02 39 9 blade: 0.4 x 2.5 x 75 mm, length: 150 mm 1 27 99 69 4 short version (without knurl) 20 2.3. General Data Plug connection Max. voltage Current carrying capacity Plug cycles Cable diameter (max./min.) Fixing screws/torque 9-pos. D-SUB pin strip 60 V AC/DC 1A > 50 10 mm/6 mm 4-40 UNC/0.4 Nm Screw terminal blocks: Connection cross section (solid/stranded/AWG) Torque Temperature range Housing material 0.14-1.5 mm2/0.14-1.0 mm2/AWG 26-14 0.4 Nm -20 °C to +75 °C ABS-V0, metal-plated PHOENIX CONTACT page 2 of 2 http://www.phoenixcontact.com Pcs. Pkt. Order No. TNR: 5087785-00 ne 1, 1, 2, 3, 6, 7 01.02.99 on l Screwdriver SZN/K Optional fixing screw, SUBCON-SHORTSCREW po om in ec 2.2. Accessories nt s. co m SUBCON-PLUS M1  PHOENIX CONTACT Type 9-pos.